Tribological behavior of Zr-based bulk metallic glass sliding against polymer,ceramic, and metal materials

The tribological properties of zirconium-based bulk metallic glass (BMG) sliding against polymers, steels, and ceramics at different loads and speeds were investigated. Acoustic emission (AE) technology was used to analyze wear states. The frictional coefficients of the BMG slid against the steel and ceramic balls were high but decreased with increased applied normal load and sliding speed. As the steel balls were more ductile than the ceramic ones, the steel–BMG sliding pairs generated weaker AE signals and exhibited larger wear rates. The BMG tested against the polymer balls had much lower and more stable frictional coefficients than the ones against the steel or ceramic balls because of transferred polymer layers on the BMG surfaces. The BMG against the polymer balls also exhibited the highest AE signals among the three types of counter materials used, indicating that abrasive wear dominated in the polymer-BMG sliding pairs. These results demonstrated the potential application of the BMG as a new tribomaterial that could be an alternative to the traditional crystalline metals for various counter materials.     

Formation of ST12 phase Ge nanoparticles in ZnO thin films

In this work, we focus on the Ge nanoparticles (Ge-np) embedded ZnO multilayered thin films. Effects of reactive and nonreactive growth of ZnO layers on the rapid thermal annealing (RTA) induced formation of Ge-np have been specifically investigated. The samples were deposited by sequential r.f. and d.c. sputtering of ZnO and Ge thin film layers, respectively on Si substrates. As-prepared thin film samples have been exposed to an ex-situ RTA at 600 °C for 60 s under forming gas atmosphere. Structural characterizations have been performed by X-ray Diffraction (XRD), Raman scattering, Secondary Ion Mass Spectroscopy (SIMS), and Scanning Electron Microscopy (SEM) techniques. It has been realized that reactive or nonreactive growth of ZnO layers significantly influences the morphology of the ZnO: Ge samples, most prominently the crystal structure of Ge-np. XRD and Raman analysis have revealed that while reactive growth results in a mixture of diamond cubic (DC) and simple tetragonal (ST12) Ge-np, nonreactive growth leads to the formation of only DC Ge-np upon RTA process. Formation of ST12 Ge-np has been discussed based on structural differences due to reactive and nonreactive growth of ZnO embedding layer.     

Measuring changing strain fields in composites with Distributed Fiber-Optic Sensing using the optical backscatter reflectometer

Background/purposeMeasurements of strains in critical components are often required in addition to finite element calculations when evaluating a structure.MethodsThis paper describes how standard optical fibers, bonded to the surface or embedded in a laminate, can measure strain fields along the entire length of the fiber, using the optical backscatter reflectometer.ResultsA strain field measurement can be much better compared to simulations than the more common single point measurements with strain gauges or Bragg Gratings. Changes of the strain field can be related to damage development and can be used for structural health monitoring. Practical aspects of using the fibers are also discussed.ConclusionDistributed Fiber-Optic Sensing was successfully embedded and bonded to a composite joint. Adhesive damage was identified and the strain field agreed well with FE-Analysis.     

Assessment of the effectiveness of steel fibre reinforcement for the punching resistance of flat slabs by experimental research and design approach

The present paper deals with the experimental assessment of the effectiveness of steel fibre reinforcement in terms of punching resistance of centrically loaded flat slabs, and to the development of an analytical model capable of predicting the punching behaviour of this type of structures. For this purpose, eight slabs of 2550 × 2550 × 150 mm³ dimensions were tested up to failure, by investigating the influence of the content of steel fibres (0, 60, 75 and 90 kg/m³) and concrete strength class (50 and 70 MPa). Two reference slabs without fibre reinforcement, one for each concrete strength class, and one slab for each fibre content and each strength class compose the experimental program. All slabs were flexurally reinforced with a grid of ribbed steel bars in a percentage to assure punching failure mode for the reference slabs. Hooked ends steel fibres provided the unique shear reinforcement. The results have revealed that steel fibres are very effective in converting brittle punching failure into ductile flexural failure, by increasing both the ultimate load and deflection, as long as adequate fibre reinforcement is assured. An analytical model was developed based on the most recent concepts proposed by the fib Mode Code 2010 for predicting the punching resistance of flat slabs and for the characterization of the behaviour of fibre reinforced concrete. The most refined version of this model was capable of predicting the punching resistance of the tested slabs with excellent accuracy and coefficient of variation of about 5%.     

Pull out of FRP reinforcement from masonry pillars: Experimental and numerical results

In this paper, debonding phenomena between carbon fiber reinforced polymer (CFRP) strips and masonry support were investigated on the basis of single-lap shear tests, considering different dimensions of the bond length. To capture the post-peak response of the CFRP–masonry joint, the slip between the support and the reinforcement strip was controlled using a clip gauge positioned at the end of the reinforcement. The tests were simulated by means of a finite element model able to capture the post-peak snap-back behavior due to the failure process. The numerical model is based on zero-thickness interface elements and on a proper non-linear cohesive law. The comparison between experimental and numerical results was performed in terms of overall response, measured by both the machine stroke and the clip gauge positioned at the free end of the reinforcement. The cases of effective bond length greater and lesser than the minimum anchorage length, suggested by the CNR Italian recommendation, were considered.     

Solidification morphology and phase selection in drop-tube processed Ni–Fe–Si intermetallics

Drop-tube processing was used to rapidly solidify droplets of Ni_64.7Fe₁₀Si_25.3 and Ni_59.7Fe₁₅Si_25.3 alloys. In the larger droplets, and therefore at low cooling rates, only two phases, γ-Ni₃₁Si₁₂ and β₁-Ni₃Si were observed. Conversely, in the smaller droplets, and therefore at higher cooling rates, the metastable phase Ni₂₅Si₉ was also observed. The critical cooling rate for the formation of Ni₂₅Si₉ was estimated as 5 × 10³ K s⁻¹. SEM and TEM analysis reveals three typical microstructures: (I) a regular structure, comprising single-phase γ-Ni₃₁Si₁₂ and a eutectic structure between γ-Ni₃₁Si₁₂ and β₁-Ni₃Si; (II) a refined lamellar structure with a lamellar spacing <50 nm comprising γ-Ni₃₁Si₁₂ and β₁-Ni₃Si; (III) an anomalous structure with a matrix of Ni₂₅Si₉ and only a very small proportion of a second, and as yet unidentified, phase. These results indicate that there is an extended stability field for Ni₂₅Si₉ in the Ni-rich part of the Ni–Fe–Si ternary system in comparison to the Ni–Si binary system. With an increase of cooling rate, an increasing fraction of small droplets experience high undercoolings and, therefore, can be undercooled into the Ni₂₅Si₉ stability field forming droplets consisting of only the anomalous structure (III). The Fe atoms are found to occupy different substitutional sites in different phase, i.e. Fe substitutes for Ni in the γ phase and Si in the L1₂ (β₁) phase respectively.     

Static stress analysis of carbon nano-tube reinforced composite (CNTRC) cylinder under non-axisymmetric thermo-mechanical loads and uniform electro-magnetic fields

Static stresses analysis of carbon nano-tube reinforced composite (CNTRC) cylinder made of poly-vinylidene fluoride (PVDF) is investigated in this study. Non-axisymmetric thermo-mechanical loads are applied on cylinder in presence of uniform longitudinal magnetic field and radial electric field. The surrounded elastic medium is modeled by Pasternak foundation because of its advantages to the Winkler type. Distribution of radial, circumferential and effective stresses, temperature field and electric displacements in CNTRC cylinder are determined based on Mori–Tanaka theory. The detailed parametric study is conducted, focusing on the remarkable effects of magnetic field intensity, elastic medium, angle orientation and volume fraction of carbon nano-tubes (CNTs) on distribution of effective stress. Results demonstrated that fatigue life of CNTRC cylinder will be significantly dependent on magnetic intensity, angle orientation and volume fraction of CNTs. Results of this research can be used for optimum design of thick-walled cylinders under multi-physical fields.     

Microstructure and mechanical properties of an Al–TiC metal matrix composite obtained by reactive synthesis

A metal matrix composite has been obtained by a novel synthesis route, reacting Al₃Ti and graphite at 1000 °C for about 1 min after ball-milling and compaction. The resulting composite is made of an aluminium matrix reinforced by nanometer sized TiC particles (average diameter 70 nm). The average TiC/Al ratio is 34.6 wt.% (22.3 vol.%). The microstructure consists of an intimate mixture of two domains, an unreinforced domain made of the Al solid solution with a low TiC reinforcement content, and a reinforced domain. This composite exhibits uncommon mechanical properties with regard to previous micrometer sized Al–TiC composites and to its high reinforcement volume fraction, with a Young’s modulus of ∼110 GPa, an ultimate tensile strength of about 500 MPa and a maximum elongation of 6%.     

Hygrothermal deformation of orthotropic nanoplates based on the state-space concept

This paper deals with the investigation of the effect of hygrothermal conditions on the bending of nanoplates using Levy type solution model employing the state-space concept. The nanoplates are assumed to be subjected to a hygrothermal environment. The two-unknown function plate theory is used to derive the governing differential equations on the basis of Eringen's nonlocal elasticity theory. The governing equations contain the small scale effect as well as hygrothermal and mechanical effects. These equations are converted into a set of first-order linear ordinary differential equations with constant coefficients. Analytical solution of bending response for nanoplates under combinations of simply supported, clamped and free boundary conditions is obtained. Comparison of the results with those being in the open literature is made. The influences played by small scale parameter, temperature rise, the degree of moisture concentration, boundary conditions, plate aspect ratio and side-to-thickness ratio are studied.     

利用HFC网络开展VoIP业务

本文首先介绍了VoIP的原理、相关协议．然后介绍了VoIP业务在HFC网络应用的业务环境和体系结构。并对其中的功能实体进行描述和说明。最后介绍一个具体的业务实例。